FAIL (the browser should render some flash content, not this).
Rolling Insulated Doors

American Door

  • Insulated Rolling Doors Specifications Series AM-625

American Door rolling insulated doors come with a foamed-in-place insulation. The insulation is ideal for reduction of building costs and optimal control of heating and cooling energy losses through openings. Neoprene hood baffle reduces air infiltration at header while guide weatherstrip at each jamb reduces air leakage between guide and curtain. American Door rolling insulated doors are available in aluminum, galvanized steel, stainless steel with operation of chain hoist, crank, and motor operation. Available to match all your color needs.


American Door Insulated Rolling Steel Service Doors combine energy efficiency with structural strength and durability, and keeping facility heat loss to a minimum. The insulated door curtains are constructed of a standard gauge front slat and a 24 gauge back slat, enclosing sections of 5/8" rigid polyurethane insulation. Front and back slats are finished with a baked-on gray finish.

American Door offers many solutions for all your rolling insulated door needs.

Click Here For RAL Powder Coated Finish Options


  1. Insulated Rolling Doors Specifications Series AM-625

    FURNISH AND INSTALL rolling service doors as indicated. Doors shall be as manufactured by American Door.
  2. WORK NOT INCLUDED unless otherwise specified: preparation of openings, steel jambs or supports, trim, access panels, field or finish painting, wiring or disconnect switches for motor operated doors.
  3. CURTAINS are to be formed of (galvanized steel), (aluminum), (stainless steel) interlocking slats designed to withstand a wind load of 20 pounds per square foot. Windlocks to be furnished where required by opening span, or for heavier windload requirements. Steel slats shall be galvanized per ASTM standards, chemically treated for paint adhesion. Both ends of alternate slats to be equipped with end locks. The bottom of each curtain shall be reinforced with two (2) (steel), (aluminum), (stainless steel) angles of equal weight or extruded aluminum bottom bar assembly standard on all doors up to 16-0 unless specified otherwise.
  4. COUNTERBALANCE ASSEMBLY shall be furnished with oil tempered helical torsion springs having a 25% safety factor. Springs shall be fixed to tapered cast anchors, mounted on a single steel torsion rod. Torsion rod to be attached to a spring adjusting wheel, adjustable without removing the hood. Entire spring assembly to be housed in a steel pipe shaft of proper diameter and thickness so not to exceed .03 of deflection per foot of span.
  5. BRACKET PLATES are to be of steel plate with sealed ball bearings to support counterbalance assembly and door curtain. Brackets to form end closures and support hood.
  6. HOODS shall not be less than 24 Gauge (galvanized steel), (aluminum), (stainless steel), contour to fit end brackets, and reinforced with stiffening beads at top and bottom edges.
  7. GUIDES are to be fabricated of (steel), (aluminum), (stainless steel) angles of not less than 3/16 thick. Depth of guides to be sufficient to retain curtain under wind load specified. If wind locks are required, guides will be furnished with wind lock retainers. Guides to be assembled with 3/8 bolts, bolted to jambs at spacing's not exceeding 3’-0 on centers, bellmouths and door stops are incorporated into guide assemblies as standard.
  8. OPERATION is to be (manual, with lift handles), (hand chain and gear, maximum of 35 pounds of pull), (hand crank gear), (motor operator).
  9. LOCKING with provision for padlocks by means of (slide bolts on manual doors), (chain lock keeper for chain operated doors), (locking disc for crank operated doors), (self-locking gearing on motor operated doors), with chain lock for emergency hand chain.
  10. FINISH steel surfaces to receive one shop coat of prime paint except galvanized surfaces, bearings, etc. For aluminum finish shall be (mill), (anodized), (duranodic). For stainless steel finish shall be (mill), (#4).


Specifications For Optional Features

MOTOR OPERATIONS to include high starting torque motor, reduction gearing, solenoid brake, limit switches for up and down door travel, emergency hand chain with electrical interlock to cut power to control switch when hand chain is engaged, magnetic relay starter with overload protection, internal pre-wiring to terminal block, three button station operating on a 24 volt control circuit. Motor is removable without affecting emergency hand chain operation. Wiring diagram provided.
REVERSING SAFETY DOOR EDGE to be furnished on motor operated doors. Upon contact with an obstruction this safety feature will stop the door and return it to fully open position.
BOTTOM ASTRAGAL as the still to be provided using tubular neoprene.
WINDLOCKS to be provided for doors exceeding 20 pounds per square foot wind load with appropriate wind lock guides.
SLOPING BOTTOM BARS to be furnished as indicated to suit sloped sill conditions.
ALL SEAL WEATHER DOOR to be provided with weather stripping around all edges, including guide weather stripping, bottom bar astragal, hood baffle and No. 5 slat.
SHOP COAT curtain and hoods shall be shop primed in addition to non-galvanized surfaces. A full range of powder coatings is also available.
VISION LITES, 1x5, to be furnished at eye level, assemble consisting of 3 lites across - 5 slats high.
EXTERIOR MOUNTING with exterior hoods and operator covers, thru wall provided when operation is desired inside - door mounted on exterior.
GALVANIZING to be applied to guides, brackets and pipe shafting in addition to galvanized parts provided in standard specifications.
FACIAS AND SOFITS to be provided, if shown to be supplied by American Door.
INSULATED SLATS shall be double faced galvanized and prime painted #4 slat with polyisocynurate.
STOPLOCK SAFETY BEARING to be furnished on motor operated doors to prevent doors from falling due to damage to motor operator, drive chain or pipe shaft.
WICKET DOORS are available. Call factory with your specifications.
CYLINDER LOCKING is to be provided on the bottom bar of the door. For motor operated doors, protective cut-out switches to be furnished.

American Door
9 Lucon Drive Deer Park, New York 11729 Headquarters
24-Hour Emergency Service 7 days a week
888-226-3667 / 718-895-6136 / 631-586-8006
Sales * Repairs * Service * Installation
Commercial | Industrial | Residential
Rolling Doors / Overhead Doors /Rolling Insulated / Rolling Fire Doors
Service Doors/ Rolling Grilles / Rolling Counter Shutters / Rolling Ventilated /Motor Operators / Sectional Steel /Sectional Steel Insulated / Sectional / Sectional Fullview / Sliding Accordion Grilles / Scissor Gates / Exit Devices / Dock Levelers /Mechanical Levelers /Hydraulic Levelers/ Edge of Docks / Dock Seals / Shelters /Fire Personnel Doors /Exit Devices / Door Closers / Impact Doors /Flex Strips / Sheet Doors / High Speed Doors / Security Fences /
Security Gates/ Custom Wood / Sliding Accordion Grilles /Residential Motor Operators /Garage Doors / Hurricane Shutters / Preventive Maintenance /Truck and Trailer Door Repair

Serving: Nassau, Suffolk, Manhattan, Staten Island, Brooklyn, Queens, Westchester, Rockland, Putnam, Orange, Dutchess, South Ulster
New Jersey, and Connecticut